PLUMBING FOR BEGINNERS: THE ESSENTIALS FOR BATHTUB INSTALLATION

Plumbing for Beginners: The Essentials for Bathtub Installation

Plumbing for Beginners: The Essentials for Bathtub Installation

Blog Article

Call Today

Right here down the page you can locate some incredibly good information involving Installing A Bathtub.


How to Install a Bathtub
Setting up a bath tub isn't exactly rocket science, however it does require solid plumbing, carpentry, and also often, tiling abilities. Changing an old bathtub with a brand-new one is likewise a moderately hard job. If the old bathtub is conveniently easily accessible, the task can relocate easily; if you need to open up a wall to get rid of the old tub and place the brand-new bathtub, the job is much harder. In either case, the job is within a residence handyman's abilities, although you will need an assistant to leave the old tub and set in the brand-new one. Ensure you have qualified yourself for the task as well as fit attempting it. Instead of hiring a service provider to take over a halfway-completed project, it is much better to think about employing one prior to you begin. Possibilities are you might need a specialist plumber to make tube links.
This article will certainly assist you install a new bathtub in your restroom if you have actually already gotten a new tub and don't need to alter the setup of your previous supply of water pipes.
Your tools and also material checklist should comprise the following:
  • New Tub
  • Hammer

  • Pipe Wrenches

  • Prybar

  • Shatterproof glass

  • Level

  • Pliers

  • Adjustable Wrench

  • Putty Blade

  • Screwdriver

  • Cold Blade

  • Tape Measure

  • Pipe Caps


  • Preparing for the Setup


    First of all, the sustaining structure provided with the bathroom needs to be fitted (if required) according to the producer's guidelines. Next, fit the faucets or mixer to the bath tub. When fitting the faucet block, it is important to make certain that if the tap features a plastic washer, it is fitted in between the bathroom as well as the faucets. On a plastic bathroom, it is likewise sensible to fit a sustaining plate under the faucets device to prevent pressure on the tub.
    Fit the versatile tap ports to the bottom of the two taps using 2 nuts and olives (often provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and then pass the electrical outlet through the hole in the bath. Make use of the nut supplied by the producer to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
    Next, fit the end of the versatile overflow pipe to the overflow outlet. Afterwards, screw the pipeline to the overflow face which ought to be fitted inside the bath. Make certain you utilize every one of the provided washing machines.
    Attach the catch to the bottom of the waste outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the electrical outlet. Attach all-time low of the overflow tube in a comparable manner.The bathroom need to currently be ready to be suited its final placement.

    Removing Old Touches


    If you need to replace old faucets with new ones as a part of your installation, then the first thing you should do is separate the water. After doing so, turn on the faucets to drain pipes any type of water staying in the system. The process of removing the existing faucets can be fairly troublesome because of the restricted accessibility that is usually the instance.
    Make use of a basin wrench (crowsfoot spanner) or a tap device to undo the nut that attaches the supply pipelines to the taps. Have a cloth all set for the staying water that will certainly come from the pipes. Once the supply pipelines have been gotten rid of, utilize the same tool to loosen up the nut that holds the faucets onto the bath/basin. You will need to quit the single taps from transforming throughout this process. When the faucets have been gotten rid of, the holes in the bath/basin will have to be cleaned of any type of old sealing compound.
    Prior to proceeding to fit the brand-new taps, compare the pipe links on the old faucets to the brand-new faucets. If the old faucets are longer than the new taps, then a shank adapter is needed for the brand-new faucets to fit.

    Installing the Bath tub


    Using the two wood boards under its feet, position the bathtub in the called for setting. The wooden boards are helpful in equally spreading out the weight of the tub over the area of the boards instead of focusing all the weight onto four tiny factors.
    The following goal is to ensure that the bath tub is leveled all round. This can be achieved by inspecting the level and also readjusting the feet on the tub till the spirit level reviews degree.
    To mount taps, fit the bottom of the outermost versatile faucet adapter to the appropriate supply pipe by making a compression sign up with; after that do the very same for the other tap.
    Switch on the water and also inspect all joints as well as new pipework for leakages and tighten them if necessary. Load the bath tub and likewise check the overflow outlet as well as the normal outlet for leakages.
    Lastly, deal with the bathroom paneling as described in the maker's instruction manual. Tiling and sealing around the bath tub needs to wait till the bathtub has been used at least once as this will settle it into its final setting.

    Suitable New Touches


    If the tails of the brand-new taps are plastic, then you will require a plastic port to prevent damages to the thread. One end of the connector fits on the plastic tail of the tap and also the other end supplies a link to the existent supply pipes.
    If you need to fit a monobloc, after that you will certainly call for reducing couplers, which connects the 10mm pipe of the monobloc to the basic 15mm supply pipe.
    Next off, place the faucet in the installing opening in the bath/basin guaranteeing that the washing machines are in location between the faucet and the sink. Secure the tap in position with the maker provided backnut. As soon as the tap is firmly in place, the supply pipes can be connected to the tails of the faucets. The faucets can either be attached by utilizing corrugated copper piping or with normal faucet connectors. The previous kind must be attached to the tap ends initially, tightening up only by hand. The supply pipelines can later on be linked to the other end. Tighten both ends with a spanner after both ends have actually been attached.

    Tiling Around the Bathtub


    In the location where the bathroom meets the floor tile, it is essential to secure the accompanies a silicone rubber caulking. This is necessary as the fitting can move enough to fracture an inflexible seal, triggering the water to pass through the wall surface in between the bathroom and also the tiling, leading to problems with moisture and feasible leaks to the ceiling below.
    You can choose from a variety of coloured sealers to assimilate your components as well as installations. They are marketed in tubes as well as cartridges, as well as are capable of securing spaces up to a size of 3mm (1/8 inch). If you have a larger space to fill up, you can load it with twists of drenched newspaper or soft rope. Bear in mind to constantly load the bathtub with water before securing, to enable the activity experienced when the bathtub remains in usage. The sealant can fracture fairly early if you do not take into consideration this motion prior to sealing.
    Alternatively, ceramic coving or quadrant floor tiles can be used to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are likewise conveniently readily available on the marketplace. It is advisable to fit the floor tiles using water-resistant or waterproof glue and cement.

    How to Install or Replace a Bathtub


    Find Your Dimensions


    The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.



    After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?


    Disconnect the Water Supply and Drain Assembly


    Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.



    Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.



    Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.


    Cut Out the Old Tub


    After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.



    Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.



    Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.


    Install the New Tub


    Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.



    Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.



    Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.



    When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.


    Secure the Tub


    After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.



    Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.



    Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.



    Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.

    https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/


    A Step-by-Step Guide to Installing a Bathtub

    I came across that blog posting about How to Install a Bathtub when doing a search on the internet. Sharing is good. Helping others is fun. Many thanks for going through it.


    This Post

    Report this page